軸受はどこだ

1 ：名無しさん＠３周年：2010/09/23(木) 21:39:40 ID:W2MRsd5C.net

軸受はどこだ！
　軸受は資源になるのか。

41 ：Spiral Groove Bearings：2010/12/01(水) 20:58:02 ID:sqmGSjgF.net

E27
Sliding Bearing of Screw Compressors(10th Report)
By spiral-groove-runner provided into the bearing device,
is doing testing for coefficient of friction.

In this the paper, researches concerning the groove condition
of spiral-grooved thrust runner on bearing.
http://jglobal.jst.go.jp/public/20090422/200902283326989138

42 ：Spiral Groove Bearings：2010/12/01(水) 21:17:52 ID:sqmGSjgF.net

T4-58
Sliding Bearing of Screw Compressors (11th Report)
Experimental study on spiral-groove type thrust bearings for
screw compressors by use of refrigerant-blended lubricant．

Tests were conducted using refrigerant-blended lubricant
simulating real conditions. Test results showed reasonable
bearing characteristics.
http://web.kanazawa-u.ac.jp/~asiatrib/FinalProgram.pdf

43 ：Spiral Groove Bearings：2010/12/01(水) 22:18:25 ID:sqmGSjgF.net

1214
Sliding Bearing of Screw Compressors(12th Report)
Testing study on spiral-groove type thrust bearings for
screw compressors by use of refrigerant-blended lubricant．
This report presents the test results of the ribbon type
bearing performance using real lubricant, blend of oil and
refrigerant．

44 ：Spiral Groove Bearings：2010/12/03(金) 21:34:43 ID:QldMbLKT.net

D7
Sliding Bearing of Screw Compressors (13th Report) :
Thrust bearings for screw compressors, experiment
by use of refrigerant blended lubricant.

In this paper, shown the testing of the ribbon type bearing performance using
and real lubricant or by using of refrigerant blended lubricant oil.
http://jglobal.jst.go.jp/public/20090422/200902240771454065

45 ：Spiral Groove Bearings：2010/12/03(金) 21:39:28 ID:QldMbLKT.net

3031
Sliding Bearing of Screw Compressors (14th Report)
The friction measurement on spiral groove type thrust bearings use of refrigerant

The objective of this paper is to design development sliding plain bearings
for hermetic screw compressors. The tests were carried out to obtain the data
for bearing performance operating at an actual condition of refrigerant-blended lubricant.
http://ci.nii.ac.jp/naid/110007085448

46 ：Spiral Groove Bearings：2010/12/03(金) 21:44:34 ID:QldMbLKT.net

F113
Sliding Bearing of Screw Compressors (15 Report)
Frictional temperature of slide thrust bearing of screw compressor

The tests were carried out to obtain the data for bearing performance operating at
an actual condition of refrigerant-blended lubricant.
The thrust bearing used here is a groove type bearing with grooves on
the runner and plane surface for the stationary side.
http://ci.nii.ac.jp/naid/110007082908

47 ：Screw Compressors：2010/12/06(月) 21:40:48 ID:U64G6JQc.net

Sliding Bearing of Screw Compressors (16th Report)
Counterclockwise possible spiral groove thrust slide temperature
and film thickness with relationship．

Using refrigerant-blended-lubricating-oil was measured in the direction of
counterclockwise of the characteristics at slide-thrust-Ribbon-type-bearings.
http://ci.nii.ac.jp/naid/110007709656

48 ：Screw Compressors：2010/12/06(月) 21:47:05 ID:U64G6JQc.net

1110
Sliding Bearing of Screw Compressors (17th Report) :
At the refrigerant used in the sliding bearing of counter clock wise
when the sliding bearing characteristic．

The objective of this paper is to design development sliding
a plane parallel surface bearings for hermetic screw compressors．
The thrust bearing used here is a groove type bearing
with grooves on the runner and plane surface for the stationary side．
This configuration of the bearing is named ‘Ribbon-Type-Bearing’.
The ribbon type bearing is intended to achieve higher load capacity
and the low bearing loss by the pumping effect and cooling effect of
the both types of grooves in comparison with a conventional spiral groove bearings．
http://jglobal.jst.go.jp/public/20090422/200902272333391190

49 ：Screw Compressors：2010/12/07(火) 21:03:23 ID:Wd8SuF30.net

E13
Sliding Bearing of Screw Compressors (18th Report)
Counterclockwise by the refrigerant for sliding thrust bearing
of friction torque.
Ribbon runner sliding thrust bearings that are reverse, using the mixed refrigerant lubricant oil.
To counterclockwise of the Ribbon runner sliding thrust bearings that revolve, using to
the refrigerant blended lubricant oil.
The bearing inner diameter is go the injection lubrication on by the refrigerant blended lubricant oil.
The bearing-load and refrigerant-quantity of refrigerant blended lubricant oil, at each parameter
was measured bearing characteristics.
http://jglobal.jst.go.jp/detail.php?JGLOBAL_ID=200902274531405654&qcompulsion

50 ：Screw Compressors：2010/12/07(火) 21:05:12 ID:Wd8SuF30.net

902
Sliding Bearing of Screw Compressors (19th Report)
Ribbon-type-bearing characteristics oｆ reversible rotation

For tested, Ribbon-type-bearing of the examined the operating characteristics.
By Rotated circumstances of ribbon runner side, the clock wise 1500rpm from,
the counter clock wise1500rpm, each measured for distance.